基于材料力学性能的最低设计金属温度曲线分析

铁素体钢在低温条件下存在明显的韧脆转变现象。为防止脆断事故的发生,需要确定铁素体钢制压力容器的最低使用温度。针对ASME中的A^D四条冲击豁免曲线,对应地选取了4种材料,基于材料实际的屈服强度和参考温度,按照ASME中豁免曲线的计算方法,计算得到4种材料的最低设计金属温度曲线,并与对应的A^D曲线对比,定量地分析ASME中豁免曲线的保守性。结果表明,ASME中的豁免曲线相对于材料自身的最低设计金属温度曲线保守性较大;韧性相近的材料被划分到不同的豁免曲线,使得韧性富裕量差异较大,对于某些材料,其断裂韧性被低估。     

河南渑池地区铝土矿工艺矿物学及锂的赋存状态研究

通过河南省渑池地区含锂铝土矿(岩)层工艺矿物学分析,查明铝土矿的物质组成、嵌布特征、伴生锂分布特征和赋存状态,为矿产综合利用提供理论依据。结果显示:该铝土矿Al2O3含量为54.8%,铝硅比值(A/S)为2.6,铝土矿层和粘土岩层中Li2O含量均高于伴生锂边界品位,粘土岩中锂更为富集；矿物组成除一水硬铝石之外,主要是以集合体形态产出的粘土矿物。采用稀酸解析、选矿测试和电子探针分析锂的赋存状态,查明矿石中锂主要是以类质同象置换形式赋存在伊利石和高岭石等粘土矿物中；选矿富锂尾矿中Li2O可富集到0.57%左右,是锂综合回收利用的重点研究对象。      

大断面切眼支护技术研究与实践

针对古城煤矿S1303综采工作面切眼的地质构造与施工条件,提出了大断面切眼采用“锚网索+π型梁棚+预注浆”联合支护方案,有效地控制了大断面切眼留顶煤施工期间的支护难题,保障了S1303综采面切眼能够满足设计要求和如期完成施工,为同类条件下的切眼施工提供了一定参考。     

Study on surface magnetization recover ilmenite from titanaugite using surfactant sodium oleate

ABSTRACT

Separation of ilmenite from titanaugite was investigated by magnetic coating. By enlarging magnetic difference between ilmenite and titanaugite, ilmenite was efficiently recovered. Scanning electron microscope and vibrating sample magnetometer results indicated that magnetite selectively coated onto ilmenite surface and increased its magnetism, which resulted in different magnetic separation behavior between ilmenite and titanaugite. FTIR and contact angle measurements confirmed that the adsorption difference of sodium oleate resulted in a stronger hydrophobicity on magnetite and ilmenite than titanaugite. Interaction energy analysis illustrated that hydrophobic association interaction on ilmenite was stronger than that on titanaugite, and which led to the selective coating of magnetite onto ilmenite.     

客车涂装底层材料配套性分析

针对南方客户在使用我司客车一段时间后，车身涂层不同程度出现了起泡的质量问题，进行了现场查看，发现起泡位置在车身左右侧蒙皮，且发生在涂层最底层。初步分析原因是热镀锌板+阴极电泳漆 +原子灰三者之间配套存在问题，通过热镀锌板 +阴极电泳漆 +原子灰三者之间的耐高温 80 ℃配套试验，以及室外曝晒试验，得出镀锌板表面是否钝化、电泳漆膜致密程度和原子灰苯乙烯含量是造成涂层底层起泡的主要原因。为了控制涂层起泡问题，重新修订了我司原子灰、镀锌板、电泳漆的技术标准以及部分工艺文件。     

离子液体体系卤水提锂的洗涤工艺研究

溶剂萃取法是盐湖提锂的重要工艺方法。采用磷酸三丁酯（TBP）/1-丁基-3-甲基咪唑双三氟甲基磺酰亚胺盐（[C₄mim][NTf₂]）离子液体体系对高镁锂比盐湖卤水中的锂进行萃取分离提取实验,对负载有机相的洗涤和反萃过程进行了研究。萃取实验：在TBP与[C₄mim][NTf₂]体积比为9∶1、相比（有机相与水相的体积比）为2∶1条件下,锂离子与其他离子的分离系数分别为β（锂/钠）=94.70、β（锂/钾）=148.85、β（锂/镁）=131.81。洗涤实验：系统考察了洗涤剂种类及浓度、相比、洗涤次数等因素对杂质离子洗脱率的影响,结果发现氯化锂和盐酸的混合溶液是从负载有机相中洗涤除去杂质离子的有效洗涤剂。洗涤过程适宜条件：洗涤剂中氯化锂浓度为4 mol/L、盐酸浓度为0.5 mol/L,相比为5∶1,洗涤次数为2次。反萃实验：用稀盐酸（1.0 mol/L）对负载有机相进行反萃取,在相比为1∶1条件下,单级反萃率达到97.81%。研究表明,离子液体体系作为一种新型萃取体系,在高镁锂比盐湖卤水中提取锂具有较好的应用前景。     

转载溜槽衬板磨损预测的DEM仿真方法

针对EDEM自动划分网格较稀疏问题,采用Hypermesh划分仿真模型网格,利用Herz-Mindlin接触理论的Archard磨损模型对转载溜槽磨损问题进行仿真,在网格单元上提取出漏斗和溜管衬板的接触能量和磨损量,分析了磨损量与接触能量的关系。假设转载溜槽衬板磨损深度为物料与溜槽衬板的使用时间为线性函数,根据现场衬板磨损量的测量值,将衬板的磨损系数关系的看作隐式的单变量方程,应用EDEM软件的仿真结果求解出磨损系数的标定值。分析了漏斗和溜管的磨损机理。该方法可用于转载溜槽的磨损预测。     

Simultaneous improvement of thermal conductivity and mechanical properties for mechanically mixed ABS/h-BN composites by using small amounts of hyperbranched polymer additives

Recently, thermal interface materials (TIMs) are in great demands for modern electronics. For mechanically mixed polymer composite TIMs, the thermal conductivity and the mechanical properties are generally lower than expected values due to the sharply increased viscosity and poor filler dispersion. This work shows that addition of a small amount of polyester-based hyperbranched polymer (HBP) avoided the trade-off in mechanically mixed ABS/hexagonal boron nitride (h-BN) composites. After adding 0.5 wt% HBP, the maximum h-BN content in the composites increased from 50 to 60 wt%. The out-of-plane, in-plane thermal conductivity, and tensile strength of ABS/h-BN with 50 wt% h-BN were 0.408, 0.517 W/mK, and 18 MPa, respectively, and were increased to 0.729, 0.847 W/mK, and 32 MPa by adding 0.5 wt% HBP, while 0.972, 1.12 W/mK, and 29.5 MPa were achieved for ABS/h-BN/HBP with 60 wt% h-BN. The morphological and rheological results proved that these enhancements are due to the improved h-BN dispersion by decreasing viscosity of composites during mixing. Theoretical modeling based on the modified effective medium theory confirmed such results and showed that the interfacial thermal resistance also decreased slightly. Thus, this work demonstrates a facile and scalable method for simultaneously improving the thermal conductivity and mechanical properties of thermoplastic-based TIMs.     

Impact of gypsum on flotation of scheelite and fluorite using sodium oleate as collector

ABSTRACT

In this study, effect of calcium and gypsum on scheelite and fluorite was investigated using sodium oleate as collector. Micro-flotation and contact angle results showed that the adsorption of calcium could inhibit the hydrophobicity of scheelite and fluorite. Moreover, sulfate could enhance the inhibition. FT-IR results showed that calcium could be priori precipitated into calcium oleate and adsorb on mineral surface. The adsorption of calcium could increase the scheelite potential to IEP, while it showed limited effect on fluorite potential. However, the interaction of calcium on scheelite and fluorite in gypsum solution was more complex than that in calcium solution.     

基于SolidWorks和三坐标测量仪的螺杆转子精滚刀建模与检测方法

介绍了基于SolidWorks软件的螺杆转子精加工滚刀的一种精确建模方法和利用该模型对滚刀的关键工序进行模拟验证的方法,同时介绍了在三坐标测量仪上利用螺杆转子精滚刀模型和曲线功能对螺杆转子精滚刀齿形进行检测的方法。